About Capsule Filling Machine
Home » News » Industry News » About Capsule Filling Machine

About Capsule Filling Machine

Views: 2     Author: Site Editor     Publish Time: 2021-12-30      Origin: Site

Introduction of Capsule Filling Machine 


The capsule filling machine adopts PLC controller, touch panel operation, frequency speed regulation, and is equipped with an electronic automatic counting device, which can automatically complete the positioning, separation, filling, locking and other actions of the capsule. 

Reduce labor intensity, improve production efficiency, and meet the requirements of pharmaceutical hygiene. The action of the machine is sensitive, filling dosage is precise and it's easy to operate. It is suitable for filling various domestic or imported capsules. It is an economical and practical equipment for filling capsule medicines in the pharmaceutical industry.


Maintenance of Automatic Capsule Filling Machine


Clean up the spare parts

  1. When the machine normally works for a long time, it is necessary to regularly clean up the direct contact parts with the medicine. When the batch of medicine is changed or the time is out of use for a long time, it should also be cleaned thoroughly.


Add lubricating oil

2. The transmission mechanism under the working table of the machine should be regularly added with lubricating oil (grease) in an appropriate amount to reduce the wear of moving parts.


Check the oil level

3. The oil quantity of the main drive reducer should be checked once a month. If it is insufficient, the oil should be added in time, and the lubricant should be replaced every six months; the indexing box of the turntable should be replaced once every 3000 hours of operation. According to experience, the general use of 90 #machine oil.


Safety clutch

4. The safety clutch plays a protective role when the machine is overloaded. The clutch should not slip when the load is normal, but it may also slip due to long-term use. When the slip occurs in normal use, the round nut of the clutch can be tightened. Some, in order to achieve the purpose of ensuring the normal operation of the machine and protecting it.


Vacuum separator

5. The vacuum separator of the vacuum system mainly plays the role of sucking the capsule into the upper and lower modules and separating the cap and the body during the filling of the hard capsule. 

If the capsule cannot be separated from the cap and the body, the subsequent filling will not be carried out. Every time the turntable of the machine rotates one station, the main shaft of the machine rotates one round, and the vacuum separator moves up and down once under the action of the cam. 

If the cap and body of the capsule are not separated smoothly, check the gap between the upper plane of the vacuum sparator and the lower plane of the lower module.

If the gap is too large, the vacuum degree of the vacuum system will not reach the vacuum degree required by the cap and body separation ( About 0.05MPa), the gap is too small and it is easy to cause head collision to deform the lower module. 

When the position of the vacuum separator needs to be adjusted, use the handle to turn the main motor shaft to raise the vacuum separator to the highest position, and loosen the lock nuts at both ends of the adjusting rod under the machine table (one is left-handed nut, another one is right-handed nut ), then rotate the adjusting rod to adjust the height of the vacuum separator, then tighten the nut, and use the handle to rotate the main motor shaft to test until it is suitable. 

The vacuum degree is read on the vacuum gauge on the machine operation panel. 

When the vacuum is too high, the vacuum degree regulating valve can be opened appropriately, and when the vacuum is too low, the vacuum degree regulating valve can be closed or closed. The filter of the vacuum system should be opened regularly to remove the clogged dirt to ensure that the vacuum system has sufficient vacuum.


Drive chain

6. The transmission chain should be checked once a week, and an appropriate amount of grease should be added, and it must be tightened again if necessary. When the chain is too loose and needs to be tightened again, the tension wheel should be moved to adjust, but the chain cannot be opened or the chain can not be separated from the sprocket, so as not to disrupt the movement sequence of the entire mechanism and prevent the interference of mechanism movement.


CONTACT US

LINK

CATEGORY

GET IN TOUCH
Gaogang Science & Technology Industrial Park, Taizhou City, Jiangsu Province China
0086-15312785805
© 2020 - Taizhou TELANG Machinery Equipment Co., Ltd. All Rights Reserved.